pnmhisteq

Updated: 10 September 2005
Table Of Contents  

NAME

pnmhisteq - histogram equalize a PNM image  

SYNOPSIS

pnmhisteq [-gray] [-rmap pgmfile] [-wmap pgmfile] [-verbose] [pnmfile]

You can abbreviate any option to its shortest unique prefix.  

DESCRIPTION

This program is part of Netpbm.

pnmhisteq increases the contrast of a PGM or PPM image through the technique of "histogram equalization."[1]

pnmhisteq computes a histogram of the luminosity of the pixels in the image. It then calculates a mapping between each luminosity and a new luminosity such that it spreads out intensity levels around histogram peaks and compresses them at troughs. It applies that mapping to the input image to produce the output image. The effect of this is that the image uses the available levels of intensity more efficiently and thereby has more visible detail.

Mathematically, the luminosity mapping is this: Assume the pixels are sorted by luminosity into B buckets numbered from 0 (lowest luminosity) to B-1. N[i] is the number of pixels in bucket i. T is the total number of pixels (sum of N[i] over all i). W is the luminosity of white.

pnmhisteq replaces an input pixel whose luminosity falls into bucket j with one whose luminosity is: 


      j
     ---
     \
      > (N[i] / T) * W
     /
     ---
     i=0

Considering a grayscale image for simplicity, this means that pixels in the most luminous bucket become white. Pixels in the 10th per centile of luminosity become 10% of white.

If you're processing a related set of images, for example frames of an animation, it's generally best to apply the same luminosity mapping to every frame, since otherwise you'll get distracting frame-to-frame changes in the brightness of objects. pnmhisteq's -wmap option allows you to save, as a PGM image, the luminosity map it computes from an image. The -rmap option causes pnmisteq to use such an image as its luminosity map.

So you can run pnmhisteq with -wmap on a composite you created with pnmcat of the images you intend to process. Then, you can run pnmisteq with -rmap on each of the individual images, using the luminosity map you generated from the composite.  

OPTIONS

-gray
When processing a pixmap, only gray pixels (those with identical red, green, and blue values) are included in the histogram and modified in the output image. This is a special purpose option intended for images where the actual data are gray scale, with color annotations you don't want modified. Weather satellite images that show continent outlines in color are best processed using this option. The option has no effect when the input is a graymap.
-rmap mapfile
Process the image using the luminosity map specified by the PGM file mapfile. The PGM image, usually created by an earlier run of pnmhisteq with the -wmap option, contains a single row with number of columns equal to the maxval (greatest intensity value) of the image plus one. Each pixel in the image is transformed by looking up its luminosity in the corresponding column in the map file (column number = luminosity) and changing it to the value given by that column.
-wmap mapfile
Creates a PGM file mapfile, containing the luminosity map computed from the histogram of the input image. This map file can be read on subsequent runs of pnmhisteq with the -rmap option, allowing a group of images to be processed with an identical map.
-verbose
Prints the histogram and luminosity map on Standard Error.
 

LIMITATIONS

Histogram equalization is effective for increasing the visible detail in scientific imagery and in some continuous-tone pictures. It is often too drastic, however, for scanned halftone images, where it does an excellent job of making halftone artifacts apparent. You might want to experiment with pnmnorm and pnmgamma for more subtle contrast enhancement.

The luminosity map file supplied by the -rmap option must have the same maxval as the input image. This is always the case when the map file was created by the -wmap option of pnmhisteq. If this restriction causes a problem, simply adjust the maxval of the map with pamdepth to agree with the input image.

If the input is a PBM file (on which histogram equalization is an identity operation), the only effect of passing the file through pnmhisteq will be the passage of time.  

SEE ALSO

pnmnorm, pnmcat, pamdepth, pnmgamma, pnm,
[1]
Russ, John C. The Image Processing Handbook. Boca Raton: CRC Press, 1992. Pages 105-110.
 

AUTHOR

Copyright (C) 1995 by John Walker ([email protected]). WWW home page: http://www.fourmilab.ch/

Permission to use, copy, modify, and distribute this software and its documentation for any purpose and without fee is hereby granted, without any conditions or restrictions. This software is provided "as is" without express or implied warranty.

 

Table Of Contents